What Is TDS in Water and What Level Is Safe for Drinking, Cooking and Industrial Use?
You have seen the number on a TDS meter. But what does it mean, and when should you worry? Here is the full answer in simple words, with the limits that matter in India.
Open any RO shop, any water purifier ad, or any family WhatsApp group in India, and someone is talking about TDS. "My water is 800 TDS, is that bad?" "The RO gives 20 TDS, is that too low?" Most people have a number but no idea what it means. This guide explains TDS from the start. You will learn what it is, what number is safe for drinking, cooking and factory use, how to test it, and what to do when it is too high or too low.
The Short Answer
TDS means Total Dissolved Solids. It is the total amount of minerals and salts dissolved in water, measured in ppm (parts per million) or mg/L. In India, BIS says drinking water should have TDS up to 500 ppm. Up to 2,000 ppm is allowed only when no better source is available. For the best taste, aim for 50 to 300 ppm. Cooking and bathing water can be a little higher. Factories need very different levels: boilers and medicine plants need near zero, while cooling towers can use more.
In This Guide
What Is TDS in Water? A Simple Explanation
Water is never just water. As it flows over rocks and soil, or through pipes, it picks up tiny bits of minerals and salts and carries them along. These bits are so small that you cannot see them. They dissolve, like sugar in tea. Together, all of these dissolved things are called Total Dissolved Solids, or TDS.
What Is Inside TDS?
Most of it is harmless minerals like calcium, magnesium, sodium, potassium, chloride, sulphate and bicarbonate. Some of it can be harmful, like nitrate, fluoride, arsenic or heavy metals. TDS adds all of them up and gives you one number. It does not tell you which ones are there.
How Is TDS Measured?
TDS is measured in ppm (parts per million) or mg/L (milligrams per litre). These two mean the same thing. If a sample has 500 ppm TDS, it holds 500 milligrams of dissolved solids in every litre of water. A handheld TDS meter does not count the solids directly. It checks how well the water carries electricity, called conductivity, and then multiplies by a factor (usually between 0.5 and 0.7) to show TDS.
Where Does TDS Come From?
Natural sources
Rocks, soil and underground layers. This is why borewell water in dry areas like Rajasthan often has high TDS, sometimes above 1,000 ppm.
Human sources
Factory waste, sewage, farm fertiliser and cleaning chemicals can all add dissolved solids to water.
Pipes and tanks
Old or rusty pipes can add metals. Salt-based water softeners can slightly raise TDS because they swap one salt for another.
The TDS Scale: What Each Number Means for Drinking Water
Here is an easy scale to read your TDS number. It combines the BIS limits used in India with the WHO taste guide.
Flat taste. Very few minerals left.
Fresh taste with healthy minerals.
Safe by BIS. Taste is fine for most people.
Over the BIS acceptable limit. Salty or bitter taste starts.
BIS allows only if no other source. Treat it.
Do not drink without treatment.
Why does this scale say 500 and not 600? The WHO taste guide calls water up to 600 ppm "good". But India follows the BIS standard IS 10500, which sets the acceptable limit at 500 ppm. In India, use 500 as your line.
The WHO has not set a health-based limit for TDS. It uses TDS as a taste guide. The WHO taste bands are: under 300 excellent, 300 to 600 good, 600 to 900 fair, 900 to 1,200 poor, and above 1,200 unacceptable.
What TDS Level Is Safe for Drinking Water in India?
The BIS Rule (IS 10500:2012)
The Bureau of Indian Standards gives two numbers for every water quality item. The first is the acceptable limit. The second is the permissible limit in the absence of an alternate source. For TDS, these are:
| Item | Acceptable limit | Permissible limit (no other source) |
|---|---|---|
| Total dissolved solids (TDS) | 500 mg/L | 2,000 mg/L |
| Total hardness (as CaCO3) | 200 mg/L | 600 mg/L |
| Chloride | 250 mg/L | 1,000 mg/L |
| Sulphate | 200 mg/L | 400 mg/L |
| BIS notes that above 500 mg/L, taste gets worse and it may irritate the stomach. The aim is always to meet the acceptable limit. | ||
The Best TDS for Daily Drinking
If you want a simple target, 50 to 300 ppm tastes best and still has useful minerals like calcium and magnesium. Anything up to 500 ppm is fine under BIS. Water above 500 ppm is not always dangerous, but the taste often turns salty or bitter, and it is not what BIS calls acceptable.
What About Bottled Water?
Packaged drinking water must follow IS 14543, and its TDS limit is a maximum of 500 mg/L. Natural mineral water is different. FSSAI guidance gives a TDS range of 150 to 700 mg/L for it, because the minerals come from the source. Standards can be revised, so check the latest version if you run a plant.
Important: A good TDS number does not mean the water is safe. Water with 150 ppm TDS can still carry bacteria, arsenic or fluoride. And water with 800 ppm TDS made of harmless minerals can be safe to drink. TDS is a first check, not the full answer. Always do a full lab test if you are unsure.
Safe TDS Levels for Cooking, Bathing, Plants and Home Use
Drinking water needs the strictest limit because you take it into your body every day. Other home uses can handle more. Here is a simple guide.
| Use | Good TDS range | What happens if it is too high |
|---|---|---|
| Drinking | 50 to 300 ppm (up to 500 is acceptable) | Salty or bitter taste. BIS says it may upset the stomach. |
| Cooking (dal, rice, tea) | Under 500 ppm | Hard water can make dal and rajma take longer to cook, and tea may look cloudy or leave a film. |
| Bathing and washing | Under 1,000 ppm is workable | Soap lathers less, clothes feel stiff, and white scale builds on taps, tiles and geysers. |
| Geyser and washing machine | As low as you can manage, and soft | Scale shortens the life of heating parts and wastes electricity. |
| Garden plants and lawns | Under about 1,500 ppm for most plants | Salt builds up in the soil and burns leaf tips. Sensitive plants suffer first. |
| Toilet flushing, floor cleaning | Any level | No big problem, apart from scale marks. |
| These are practical guides, not legal limits. Hardness matters as much as TDS for cooking, bathing and appliances. | ||
Is Very Low TDS Water Bad?
Many families with RO purifiers see a reading of 10 to 30 ppm. That water has almost no minerals. It is clean, but it can taste flat. Some experts and the WHO advise that people who drink only demineralised water should get calcium and magnesium from food or through a mineral cartridge. A healthy diet gives most of your minerals, so low TDS is not an emergency. But it is a good reason not to run an RO on water that is already low in TDS.
What TDS Level Is Right for Industrial Use?
In industry, the right TDS depends on what the water does. Some jobs need water that is almost pure. Others can use water that would be undrinkable. Using the wrong water is expensive, so this is where TDS control saves real money.
| Industrial use | Typical target | Why it matters |
|---|---|---|
| Boiler feed water (low pressure) | Very low, with hardness near zero | Hardness makes scale on boiler tubes, which wastes fuel and can burst tubes. Boiler water inside a low pressure boiler is usually kept below about 3,500 ppm by blowdown. |
| High pressure boilers and turbines | DM water, close to 0 ppm | Even tiny salts cause deposits and damage at high temperature. Always follow your boiler maker. |
| Cooling tower makeup | Often 400 to 1,000 ppm workable | Water is reused many times and gets saltier. If you allow 2,000 to 3,000 ppm in the loop and run 3 to 5 cycles, makeup of 400 to 1,000 ppm works. |
| Food and beverage | Usually under 500 ppm, many aim lower | Taste, colour and product shelf life depend on clean, soft water. Follow your product specification. |
| Medicine and lab water | Below 1 ppm (conductivity near 1.3 µS/cm or less) | Purity rules are very strict. Needs RO plus further polishing. |
| DEF (AdBlue) making | Conductivity under 0.5 µS/cm | Any extra salt can damage vehicle emission systems. RO alone is not enough. |
| Cleaning and dust control | Almost any level | Water quality matters little. RO reject water often works well here. |
| These are general guides. Your equipment maker, product standard or regulator sets the final limit. | ||
The cooling tower sum, step by step: If your tower allows 2,000 ppm in the circulating water and you run it at 4 cycles of concentration, then makeup water can be about 2,000 ÷ 4 = 500 ppm. That is why high TDS borewell water often needs RO or softening before it goes to a cooling tower.
What TDS Does Not Tell You
Many people trust the TDS meter too much. It is a handy tool, but it has limits.
Germs
TDS cannot show bacteria, viruses or other germs. Water with perfect TDS can still make you sick.
Harmful metals
Arsenic and lead are harmful at tiny amounts. The BIS limit for both is just 0.01 mg/L, far too small to change TDS much.
Fluoride and nitrate
Fluoride (BIS acceptable limit 1.0 mg/L) and nitrate (45 mg/L) can be above the limit while TDS looks normal.
Which minerals
Calcium and magnesium are healthy. Too much sodium or sulphate is not. TDS adds them all into one number.
TDS and Hardness Are Not the Same
Hardness counts only calcium and magnesium. TDS counts everything dissolved. A water sample can have high TDS but moderate hardness, or the other way round. BIS sets hardness at 200 mg/L acceptable and 600 mg/L permissible. If you have scale on taps and geysers, hardness is the real problem, and a softener helps more than an RO.
How to Check TDS and How to Reduce It
Test TDS at Home in 5 Steps
Use a clean glass
Rinse a glass with the water you want to test. Soap or old water in the glass will give a wrong reading.
Fill and dip the meter
Fill the glass. Switch on the meter and dip the tip up to the marked line. Do not dip the whole meter.
Wait and tap
Tap gently to remove air bubbles. Wait about 10 seconds until the number stops changing.
Note the number
Write it down. Test again at a different time. Borewell and tanker water can change from day to day.
Confirm with a lab if it matters
Cheap meters can be off by 10% or more. For a plant, business or health worry, get a NABL lab test. It costs about ₹3,000 to ₹8,000 and checks far more than TDS.
What Reduces TDS and What Does Not
| Method | Reduces TDS? | Good to know |
|---|---|---|
| Reverse osmosis (RO) | Yes, by about 90% to 99% | Best for high TDS. Wastes some water as reject, which can be reused for cleaning and gardens. |
| DM plant (ion exchange) | Yes, to near zero | Used in boilers, labs and DEF plants. Needs acid and alkali for regeneration. |
| Distillation | Yes | Very pure water, but slow and uses a lot of energy. |
| Water softener | No | Removes hardness only. Swaps it for sodium, so TDS stays about the same. |
| Boiling | No | Kills germs, but as water evaporates, TDS actually goes up. |
| UV purifier | No | Kills germs only. |
| Carbon or sediment filter | No | Removes chlorine, smell and dirt, not dissolved salts. |
When is RO needed? If your TDS is above 500 ppm, RO is usually the right answer. If your TDS is already below 500 and your lab report shows no harmful items, you may not need an RO at all. In 2019, the National Green Tribunal told the government to restrict RO where TDS is below 500 and to push for at least 60% water recovery. A draft notification followed in 2020. Rules can change, so check the latest position before you buy.
TDS is the first question to ask about your water, never the last. A number tells you where to look. A lab report tells you what to do.
Frequently Asked Questions About TDS in Water
QWhat is TDS in water?
QWhat is a safe TDS level for drinking water in India?
QIs 500 TDS water safe to drink?
QIs 1000 TDS water safe to drink?
QWhat is the ideal TDS for drinking water?
QIs low TDS water harmful?
QWhat TDS is good for cooking?
QDoes boiling water reduce TDS?
QDo UV or carbon filters reduce TDS?
QHow do I check TDS at home?
QWhat is the TDS limit for packaged drinking water and mineral water?
QWhat TDS is suitable for boilers, cooling towers and industrial processes?
QDo I need an RO if my TDS is below 500?
QWhat is the difference between TDS and hardness?
This guide is for general information. Limits and standards change, and the right level depends on your use and local rules. For health concerns, talk to a doctor. For plant or industrial design, confirm limits with your equipment maker and a qualified water treatment engineer.
Know Your Number. Then Fix What Matters.
TDS is a simple number with big meaning. Too high, and your taste, your appliances and your factory equipment all suffer. Too low, and you may be paying to remove minerals you actually need.
The right fix starts with a proper water test. Then you choose the right treatment, whether that is an RO plant, a softener, a DM system or just a simple filter.
At Kaveri RO, we design water treatment for homes, factories, bottle plants and industry across India. Share your water report and your use, and we will tell you plainly what you need, and what you do not.